Menu
1) Cutting sequence: the green line is the first cut, the red line is the second cut, and the last hole is dug.
2) If there is a bridge cutting machine and the four sides do not need to be chamfered, you can cut the green line and the red line with the bridge cutting machine and then dig the hole.
3) In case of hole digging crack, please dig 4 small circles with diameter of 30mm as shown in the figure before digging.
Note: Since the order placing position is outside the plate, the plate used to determine the origin and other plates beside it shall not be higher than the plate to be cut.
-----Handling-----
1) The manual suction tray can be installed on the other side of the big board for easy movement.
2) Install the metal support on the back of the big board, and fix rt on the big board to increase the stability of the big board.
3) It is suggested that truck transportation and forklift trucks be lifted to reduce the damage of the fixed plate.
-----Driling-----
1) The manual cutting machine can cut the square adjusting holes on the large plate at any time.
2) Use a glass knife that cuts straight lines to cut down on the glaze of a large plate for easy cutting.
3) Once the ceramic plate is drilled or cut, It must be carefulty handled and placed.
-----Cutting-----
1) It is suggested that the cutting route should be planned before cutting the big board.
2) Use a glass knife that cuts straight lines to cut down on the glaze of a large plate for easy cutting.
3) Use the cutting machine to cut along the cutting line, grinding paper to smooth the sharp edges.
-----Paving-----
1) Use the scraper to spread the adhesive on the floor and the big board, and smear it flat to facilitate the placement.
2) After big board paving, please reserve 2mm space to prevent cold shrink and heat rise.
3) After laying, the large plate is compacted, so that the inner layer is completely combined to ensure smooth surface.
1) Cutting sequence: the green line is the first cut, the red line is the second cut, and the last hole is dug.
2) If there is a bridge cutting machine and the four sides do not need to be chamfered, you can cut the green line and the red line with the bridge cutting machine and then dig the hole.
3) In case of hole digging crack, please dig 4 small circles with diameter of 30mm as shown in the figure before digging.
Note: Since the order placing position is outside the plate, the plate used to determine the origin and other plates beside it shall not be higher than the plate to be cut.
-----Handling-----
1) The manual suction tray can be installed on the other side of the big board for easy movement.
2) Install the metal support on the back of the big board, and fix rt on the big board to increase the stability of the big board.
3) It is suggested that truck transportation and forklift trucks be lifted to reduce the damage of the fixed plate.
-----Driling-----
1) The manual cutting machine can cut the square adjusting holes on the large plate at any time.
2) Use a glass knife that cuts straight lines to cut down on the glaze of a large plate for easy cutting.
3) Once the ceramic plate is drilled or cut, It must be carefulty handled and placed.
-----Cutting-----
1) It is suggested that the cutting route should be planned before cutting the big board.
2) Use a glass knife that cuts straight lines to cut down on the glaze of a large plate for easy cutting.
3) Use the cutting machine to cut along the cutting line, grinding paper to smooth the sharp edges.
-----Paving-----
1) Use the scraper to spread the adhesive on the floor and the big board, and smear it flat to facilitate the placement.
2) After big board paving, please reserve 2mm space to prevent cold shrink and heat rise.
3) After laying, the large plate is compacted, so that the inner layer is completely combined to ensure smooth surface.
Italian Design & Spanish Glaze
Italian Design
Spanish Glaze
Italian Design Spanish glaze
Italian Design Spanish glaze
Italian Design Spanish glaze
Italian Design Spanish glaze
Italian Design Spanish glaze
Italian Design Spanish glaze
Italian Design Spanish glaze
Italian Design Spanish glaze
Italian Design Spanish glaze
Italian Design Spanish glaze
Italian Design Spanish glaze
Italian Design Spanish glaze
0
